P0449 OBD II Trouble Code
If your Check Engine Light is shining and your OBD-II scan tool displays the code P0449, it’s time to familiarize … Continued
If your Check Engine Light is shining and your OBD-II scan tool displays the code P0449, it’s time to familiarize yourself with the basics of the “Evaporative Emission Control System Vent Valve/Solenoid Circuit Malfunction”.
The Meaning and Cause of the P0449 Code
Before we get into the details behind the meaning of the code P0449, let’s start with some basics: is this a manufacturer-specific or a generic diagnostic trouble code (DTC)? Luckily, it’s a generic powertrain code, meaning it’s pretty easy to find its definition and explanation online as it applies to all newer vehicles equipped with the OBD-II system. However, even though the meaning is pretty much the same across the spectrum, the exact repair steps usually vary from model to model of the vehicle.
So, what is the meaning of P0449 code? While the code’s definition – Evaporative Emission Control System Vent Valve/Solenoid Circuit Malfunction – sounds lengthy and complicated, the meaning behind it is fairly simple. Whenever it shows up, it means there is a malfunction within the Evaporative Emission Control (EVAP) system’s vent control circuit. In other words, a part of the EVAP control system is not functioning as it should.
In case you’re wondering, the EVAP system consists of various components, including the fuel tank and fuel lines, fuel vapor hoses, gas cap, charcoal canister, fuel tank pressure and flow sensors, electrical wiring and connectors and a few other parts. The function of the EVAP system is to seal the fuel system to prevent fuel vapors from the fuel tank and system from escaping into the atmosphere. If your vehicle’s Powertrain Control Module (PCM), and by extension Engine Control Module (ECM) detects a fault with the circuit that controls the vent or solenoid for the EVAP system, it means that the fuel vapors are now escaping into the air, form smog.
What causes the code P0449? Because the EVAP system is quite big, there can be quite a number of reasons for this code, but the most common ones include:
- Faulty vent/solenoid valve
- Improperly installed fuel cap
- Short or open in the wiring harness/wire circuit problem
- Clogged or damaged charcoal canister vent valve
- Broken or damaged fuel vapor or vacuum hoses
- Faulty pressure or flow sensor
- Faulty PCM or ECM (rare).
The Symptoms of the P0449 Code
Besides the illuminated Check Engine Light, it’s possible to not experience/notice any other symptoms when the P0449 code shows up. That being said, most drivers will experience the two following symptoms:
- Check Engine Light is on
- Fuel vapor odor coming from the vehicle
Notice that there are no drivability issues.
Diagnosing and Repairing the P0449 Code
Although this code doesn’t cause drivability issues, it’s important to fix it as soon as possible to prevent any further damages to the vehicle. The only problem is, the vent valve/solenoid is a part of a rather complex evaporative emissions system, meaning it can be difficult to both diagnose it properly and repair it. For this reason, it’s advisable to let a professional repair your vehicle – unless, of course, you have enough automotive knowledge.
In any case, this is how you or your mechanic should diagnose the P0499 code:
- Connect the OBD-II scanner to the DLC port, noting all stored codes and freeze frame data. Often, P0449 will turn up in combination with other EVAP system codes, and it’s important to note any and all codes to properly fix P0449. Freeze frame data is also of great importance as it gives insight into the conditions the vehicle was under when the DTC showed up.
- Clear all codes and take the vehicle on a test drive to confirm symptoms.
- Start the inspection of the vehicle. First, check if the gas cap is properly installed, and tighten it if necessary. Inspect it for physical damage too (it’s worth noting that this type of damage is not always vsible to the naked eye, so sometimes, replacing the gas cap may be necessary even if it doesn’t look damaged). Then, inspect the EVAP hoses; look for cracked or disconnected ones and connect/replace as necessary. Now switch to the fuel tank and charcoal canister; look for physical damage and/or leaks and replace whatever needs replacing. Pay special attention to the canister vent valve and test it for power. Also inspect the wiring harness.
- Finally, check if there is a disconnection between the vent wiring and the ECM, and perform a test on the ECU. Although a faulty ECM is a rarity, it’s important to be thorough.
Note: every time you perform a repair on a part, clear the code.
To sum up, these repairs can fix the code P0449:
- Fixing or replacing the gas cap
- Fixing or replacing the EVAP hoses
- Fixing or replacing the fuel tank and charcoal canister and vent valve
- Repairing faulty electrical connections
- Replacing a faulty ECM.
Bear in mind that to properly fix the P0449 code, you first need to thoroughly inspect your vehicle. Diagnosis mistakes can be made with any DTC, including this one, so it’s crucial to inspect the vehicle in detail, and then connect/repair and replace parts as necessary. It’s also worth mentioning that EVAP system components are often replaced in error, when something as simple as an improperly installed/loose fuel cap is present. To avoid common misdiagnosis, a thorough inspection is a must.
Additional Information about the P0155 Code
To diagnose EVAP system codes such as the code P0449, advanced scan tools are more often than not necessary. This is because the EVAP system needs to pass certain test procedures in order to be thoroughly checked, which is not possible without advanced scan tools. For this reason, when dealing with this DTC, it’s best to hire a professional who has all the necessary tools and can make a proper diagnosis, as that’s the only way to repair the code, and save money long-term.
Although the P0499 code doesn’t pose serious danger to the driver, whenever the Check Engine Light shines, it’s crucial to deal with the problem as soon as possible to avoid any further damage to the vehicle and its components. But when it comes to the P0449 code, it’s even more important to fix the problem as quickly as possible. This is because when a component of the EVAP system is not working properly, fuel vapors from the fuel tank and system are free to escape into the atmosphere, causing smog, a type of severe air pollution. If not dealt with, the vehicle will pollute all time, even without being turned on. As you can imagine, this is a huge problem for the environment, so the moment your OBD-II scan tool reads P0499, try your best to fix it as soon as possible.
These links will provide more detailed insights into what code means in your vehicle:
Be sure to also read our essential guide to the best OBD2 Scanner.